Floor Free Standing Portable Display Expo Retail Shop

	Title: Body Shop Poster Pole Stand Client: The Body Shop Size: 420mmW x 1600mmH x 300mmD This pole stand with an A2 poster holder on the top was developed especially for the Body Shop chain in New Zealand. The poster can be slid out sideways and the base cone base is heavily weighted for extra stability. The construction is mainly steel with a dark powder coated finish.
	Title: Body Shop Poster Pole Stand Client: The Body Shop Size: 420mmW x 1600mmH x 300mmD This pole stand with an A2 poster holder on the top was developed especially for the Body Shop chain in New Zealand. The poster can be slid out sideways and base cone base is heavily weighted for extra stability. The construction is mainly steel with a dark powder coated finish.
	Title: Card Board Dump Bin Client: Display Tactix Size: 500mmW x 800mmH x 600mmD This is an off-the-shelf “dump bin”. It comes folded flat for easy shipping and available in white, but with a large enough production run the bin can be printed in full colour with appropriate branding and transformed into a very eye catching display bin for retail products.
	Title: Coffee Table Display Case Client: Portfolio By Design Size: 1300mmW x 600mmH x 700mmD This coffee table was designed to match the existing furniture in a company reception area. The frame was provided by the client and our brief was to create, within the frame a solid display case with a toughened glass top. Inside the case, a glass artwork was to be displayed. The main case is made in 10mm clear acrylic and held together with stainless steel cabinet fixings and the base is matt opal acrylic and the top 6mm toughened glass.
	Title: Dux Demonstration Unit Client: DUX Size: 1000mmW x 1300mmH x 400mmD This unit was made to visit trade shows and demonstrate the in-ground drainage system DUX produces. The bottom plinth was MDF clad in opal acrylic with the DUX logo added with computer cut vinyl lettering. The top section was also MDF clad in dark blue acrylic with the in-ground trays and sump mounted into the top part of the unit. A pump circulated water around the system to show how the runoff from different ground surfaces was collected. The graphic panel at the back is digitally printed and applied to panel.
	Title: Expanda Foyer Stand Client: Display Tactix Size: 450mmW x 1400mmH x 500mmD This is an imported Brochure Display System from the Expanda range. It is a modular system that uses a range of injection-moulded pockets that can clip together into various combinations. This picture shows 20x DLE brochure holders fitted to a Foyer Stand.
	Title: K&D Brochure Stand Client: Display Tactix Size: 240mmW x 1350mmH x 350mmD This stand holds 4x A4 brochures in near-unbreakable PET-G pockets. The rest of the stand is plywood, with the main strut being curved to shape by a tensioned wire at the back. This is just one of a range of imported Italian display products. The range is excellent and while many items are in stock, the complete range can be ordered with shipping coming directly from our overseas supplier.

	Title: Lecturn Stand Client: Display Tactix Size: 450mmW x 1200mmH x 400mmD This lectern base and frame are one of the many units we have to hold signs. This unit has a very sturdy steel base and aluminium pole. The top in this case is a fine-rimmed A3 snap frame, but many other tops are available. This is available in Landscape or portrait.
	Title: Moa Point Model Cover Client: Clear Water Size: 1100mmW x 1400mmH x 1100mmD Hold your nose if you have smell-o-vision! This is a model cover housing the Moa point treatment plant! We were given the model on a wooden base, it fell to us to design and have a table frame made for underneath and to construct a clear acrylic model cover for over the top. The base is a powder coated tube metal and the case is 4.5mm clear acrylic.

	Title: Information Brochure Board Client: St James Theatre Size: 600mmW x 1000mmH x 500mmD This unit is made with furniture grade plywood, which is given a clear coat to bring out the natural beauty of the timber. A hinged leg allows the board to stand securely. The brochure pockets are made to fit DLE sized brochures and are designed without dividers. They are made in 4.5mm glass-tint acrylic with custom turned detail “nubs” at each end of the shelf. The St James logo and text is computer cut sign writing vinyl, which is applied as the finishing touch.
	Title: TAB Barrel Client: NZ Racing Board Size: 650mmW x 1200mmH x 450mmD These custom designed spinning barrels were produced for the TAB (NZ Racing). They were made to break down for easy shipping around to various pub events. The barrel is a clear acrylic bin, which spins on a steel frame, powder coated blue with a poster holder below for event information.
	Title: Teleflora Footpath Sign Client: Teleflora Size: 520mmW x 700mmH x 520mmD This prototype sign uses a black steel base with computer cut vinyl lettering, the frame is steel, powder coated black with a A2 snap frame attached to each side.
	Title: Expo Stand Client: Display Tactix Size: 450mmW x 1100mmH x 600mmD These plinths were first designed for use in our tradeshow booth and later adapted and refined into what you see here which is an entry form plinth. We have made several of these to go into the entrance of malls for competition entries. The main body of the unit is MDF with frosted acrylic flexed around the front and back and coloured polypropylene (several colours to choose from) flexed inside. These plinths can also be illuminated.
	Title: Visitor Book Stand Client: Parliamentary Service Size: 800mmW x 1200mmH x 450mmD The lectern holds the visitors’ book at the Beehive, and was designed especially to hold the very wide open book. It is made in powder coated steel tube and sheet with 10mm clear acrylic on the top with applied frosted sign writing vinyl.
	Title: Police Museum Lecturn Client: NZ Police Museum Size: 500mmW x 900mmH x 400mmD This bookstand was made for the children’s area at the NZ Police Museum. It has a ledge for a book and a shelved cabinet with lighting to display a few museum objects. Access to the inside of the cabinet is from the back, with an opaque door at the front which can be opened to see inside, the objects are secured behind a clear inner panel.
	Title: Pull Up Banner Client: Display Tactix Size: 700mmW x 1700mmH x 300mmD The Pull-Up Banner display is a very popular solution when portability is required. The banner rolls away into a small area and the tensioning system breaks down into short lengths so as to fit everything in a small bag. The graphics for the banner are a full colour digital print and many option and sizes are available.
	Title: Portable Brochure Stand Client: Display Tactix Size: 700mmW x 1350mmH x 400mmD This aluminium frame brochure unit is one of many in the range that use a semi-modular design. This unit has 2x tiers of A4 pockets and 1x tier of DLE pockets, but the acrylic pockets could be swapped out for a different combination. This unit folds flat for easy portability and has a sign at the top that can have graphics applied.
	Title: A4 Acrylic Pole Stand Client: Massey University Size: 400mmW x 1000mmH x 300mmD This stand is one of our oldest products and is very popular still today. The base and pole are aluminium and can be powder coated to any colour. The base is heavily weighted for stability. This image shows the A4 poster top, but we have several other tops to choose from and also make custom bins to suit special flyers.
	Title: Aquarium Client: Art of Aquaria Size: 500mmW x 1800mmH x 500mmD For years we have manufactured very high quality upright aquariums. This aquarium was made for Art of Aquaria, an Australian based rental aquarium company. They provide fully serviced aquariums that they keep to the highest professional standards.
	Title: Pet Store Pfizer Stand Client: Draft FCB Size: 450mmW x 1700mmH x 450mmD This display stand was designed to go into vet stores to promote the good health of cats and dogs through the use of flea and worming treatments. The main stand is based on a tall aluminium pole with a steel base. The triangular body of the unit is made using lightweight ACM (Aluminium Composite Material) which comes with the black finish, among other colours. The brochure pockets and poster holders are clear acrylic. The main body spins when pushed.
	Title: Noel Leeming Wonder Wheel Client: Draft FCB Size: 900mmW x 2200mmH x 800mmD This is one of the more unusual items we have made recently – each of the Noel Leeming store required a “Wonder Wheel” for a promotion. The body of the stand is white Meltecca and disc is ACM (Aluminium Composite Material). The graphics were screen printed onto paper so that the promotion could be easily updated. The wheel is spun by hand and stops with the clacker at the top.